The noise problem of industrial production and processing has been perplexing people, especially for mechanical equipment such as foam carving machine. The following contents discuss and study the noise generation and processing of the foam engraving machine.

無論是哪種型號體積的泡沫雕刻機，在其工作過程中難免會產生一定的噪聲，這主要由以下幾個方面產生。一是泡沫雕刻機的主軸電機處于運行狀態是的噪音，二是泡沫雕刻機各軸向運行或者移動過程中所發出的異常噪音。

No matter which type of volume of the foam carving machine, it will inevitably produce some noise in its work process, which is mainly caused by the following aspects. First, the spindle motor of the foam engraving machine is in the running state of noise, and the two is the abnormal noise emitted by the foam engraving machine during the axial running or moving process.

泡沫雕刻機主軸發出噪音的原因可能有很多，除了主軸電機質量欠佳等質量問題以外，泡沫雕刻機主軸的長時間使用而導致的磨損也會使其產生的噪音變得更嚴重。因而，在經過專門的針對性檢查工作后如果確定是泡沫型雕刻機主軸電機的相關問題，就需要及時對其進行拆卸維修或者更換工作，因?yàn)楫惓５脑胍粢苍谝欢ǔ潭壬舷笳髦鄳?yīng)的質量隱患，一定要嚴加重視。

There are many reasons for the noise of the spindle of the foam carving machine. Besides the quality problems such as poor quality of spindle motor, the wear caused by the long time use of the spindle of the foam carving machine will make the noise generated by it more serious. Therefore, after a specific targeted inspection work, if it is determined to be related to the spindle motor of the foam engraving machine, it needs to be dismantled and repaired or replaced in time, because the abnormal noise also symbolizes the corresponding quality and safety risks to a certain extent, so we must pay more attention to it.

而對于泡沫雕刻機工作軸所對應的異常噪音，一般來說，都是因?yàn)榕菽窨虣C(jī)的軸出現了清潔不到位、連接過緊、滾珠磨損等問題，這時候要做的就是對泡沫雕刻機進行相應的清理工作及潤滑工作，同時及時更換滾珠，從而就可以有效地減少泡沫雕刻機噪音的出現。

The abnormal noise corresponding to the working shaft of the foam engraving machine is generally due to the fact that the shaft of the foam carving machine is not clean enough, the connection is too tight, and the ball wears out. This time, we need to do the cleaning and lubricating work of the foam engraving machine, and replace the ball in time. So that the noise of foam carving machine can be effectively reduced.

泡沫雕刻機處于正常的工作狀態中也是存在一定的噪音的，但是如果出現異常的噪音，一定不能忽視，及時進行處理才能不影響后續的工作流程。

Foam carving machine in normal working condition is also there is a certain noise, but if there is abnormal noise, we must not neglect, timely processing can not affect the subsequent work process.