聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
業內資訊
日常我們該如何保養雕刻機？
來源：http://m.hbwudeli.com.cn 時間：2021-04-12
1.開機前檢查各部件是否在正常位置，各運動部件是否完好，導軌有油潤滑，然后開機底速動轉1~2分鐘，觀察是否有異常情況，等機床運轉正常后方能進行工作；
1. Before starting the machine, first check whether the parts are in normal position, whether the moving parts are in good condition, and whether the guide rail is lubricated with oil. Then start the machine and rotate it at the bottom for 1 ~ 2 minutes to observe whether there is any abnormal situation, and wait for the machine to work normally;
2.工情況選擇刀具、轉速、進刀量、加工速度及順，逆銑方向；
2. Select the tool, speed, feed, processing speed and the direction of forward and reverse milling according to the working conditions;
3.整個加工過程不能用手或碎布等雜物接觸正在轉動的刀具，在清理石粉時要確保刀具完全停止運轉才能；
3. During the whole machining process, it is not allowed to use hands or rags and other debris to contact the rotating cutting tool. When cleaning the stone powder, it is necessary to ensure that the cutting tool stops completely;
4.作業完畢，關閉電源，各部位石粉，雜物。其他相關輔助工具必須放還原處；
4. After the operation, turn off the power and remove the stone powder and debris. Other relevant auxiliary tools must be put in the reduction place;
5.定期（依使用情況）清理電器箱內灰塵，檢查接線端子螺絲是否松動，以保證機器電路，可靠使用；
5. Clean up the dust in the electrical box regularly (according to the use situation), and check whether the terminal screw is loose, so as to ensure the safe and reliable use of the machine circuit;
6.工作臺面及導軌每天擦拭干凈，不可有石粉、油污雜質等；
6. Clean the worktable and guide rail every day without stone powder, oil, impurities, etc;
7.連續運行要保證冷卻水的潔凈及冷卻機的正常工作，絕不可以使水冷主軸電機出現缺水現象，定時更換冷卻水，以防止水溫過高；
7. The continuous operation should ensure the clean cooling water and the normal operation of the cooler. The water-cooled spindle motor must not be short of water. The cooling water should be replaced regularly to prevent the water temperature from being too high;
8.定期依使用情況）檢查機器各部件螺釘是否松動，以保證機器可靠；
8. Regularly check whether the screws of all parts of the machine are loose to ensure the reliability of the machine;
9.每次機器使用完畢，要注意清理，務必將平臺及傳動系統上的粉塵清理干凈，定期（每周）對傳動系統（X,Y,Z,A,C等軸）潤滑加油；
9. Pay attention to clean up the dust on the platform and transmission system after each use of the machine, and lubricate the transmission system (x, y, Z, a, C, etc.) regularly (weekly);
10.機器若長時間不使用，應定期（每周）加油空走，以保證傳動系統的靈活性；
10. If the machine is not used for a long time, it should be refueled regularly (weekly) to ensure the flexibility of the transmission system;
11.主軸、工作臺和導軌面嚴禁敲打和沖擊，工作臺及道軌面不得亂放工具和毛坯及不相關的工件或物品；
11. It is strictly forbidden to knock and impact the spindle, worktable and rail surface, and tools, blanks and irrelevant workpieces or articles shall not be placed on the worktable and rail surface;
以上就是小編為大家介紹保麗龍雕刻機的相關內容，希望可以幫助到大家，更多精彩內容請大家直接關注：http://m.hbwudeli.com.cn
The above is Xiaobian's introduction to the relevant content of styrofoam engraving machine. I hope it can help you. For more wonderful content, please pay attention to: http://m.hbwudeli.com.cn
- 上一篇：木工雕刻機如何操作不傷臺面？
- 下一篇：石材雕刻機可用于哪些材料的雕刻工作呢？
