開料機系統顯示重啟系統并做回零操作怎么辦 。
How to restart the system and return to zero operation.
，操作者必須要對數控開料機非常熟悉，不論是說開料機的結構、應用范圍還是說開料機的技術規范以及使用時必須遵守的守則，都必須做到了熟于心，以免在使用時發生意外。另外在進行正式的操作之前，一般都要求操作者進行考試，只有考試合格的方可進行數控開料機的操作。
First of all, the operator must be very familiar with the CNC cutting machine, whether it is to say that the structure of the cutting machine, the scope of application, or the technical specifications of the cutting machine and the safety rules that must be observed when using, they must be familiar with the heart, so as to avoid accidents in use. In addition, before the formal operation, the operator is generally required to take an examination. Only those who pass the examination can operate the CNC cutting machine.
雙工序開料機一旦進行操作，就非常容易發生意外，對機器以及設備操作者都造成非常---的損傷，所以必須要引起各部門的高度重視。
Once the double process cutting machine is operated, it is very easy to cause accidents, which will cause great damage to the machine and equipment operators. Therefore, it is necessary to attach great importance to it by all departments.

雙工序開料機用久了也會出現這樣那樣的毛病，下面就跟小編一起來看看該如何保養雙工序開料機生產設備吧：
The double process cutting machine will also have such and other problems after a long time of use. Let's take a look at how to maintain the production equipment of the double process cutting machine with the help of small knitting machine
一、連續運行時間每天10小時以下，冷卻水的清潔及水泵的正常工作，絕不可使水主軸電機出現缺水現象，定時更換冷卻水，以防止水溫過高。冬季如果工作環境溫度太低可把水箱里面的水換成防凍液。
1、 The continuous operation time is less than 10 hours per day. The cleaning of cooling water and the normal operation of the water pump can never cause water shortage of the water spindle motor. Replace the cooling water regularly to prevent the water temperature from being too high. In winter, if the working environment temperature is too low, the water in the water tank can be replaced with antifreeze.
二、每次機器使用完畢，要注意清理，務必將平臺及傳動系統上的粉塵清理干凈，定期(每周)對傳動系統(x、y、z三軸)潤滑加油。(注：x、y、z三軸光桿用機油進行保養;絲桿部分加高速黃油;冬季如果工作環境全自動電腦雕刻機溫度太低絲桿、光桿(方形導軌或圓形導軌)部分應先用汽油進行沖洗清潔，然后加入機油，否則會造成機器傳動部分阻力過大而導致機器錯位。)
2、 Every time the machine is used, attention should be paid to cleaning. The dust on the platform and transmission system must be cleaned, and the transmission system (x, y, Z three axes) should be lubricated regularly (weekly). (Note: X, y, Z three-axis polished rod is maintained with oil; high-speed grease is added to the screw rod; in winter, if the temperature of the full-automatic computer engraving machine is too low, the screw rod and polished rod (square guide rail or circular guide rail) should be washed and cleaned with gasoline first, and then oil should be added. Otherwise, the resistance of transmission part of the machine will be too high and the machine will be misplaced. )
雙工序開料機
Double process cutting machine
三、對電器進行保
3、 Protect electrical appliances
養檢查是，一定要切斷電源，待---無顯示及主回路電源指示燈熄滅后，電腦木工雕刻機可進行。
Maintenance inspection is, must cut off the power supply, until --- no display and the main circuit power indicator light off, computer woodworking engraving machine can be carried out.
四、長期不使用本機時，應把各部分擦拭干凈，并用塑料或篷布覆蓋防塵。
4、 When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.